Difference between revisions of "Reprap Huxley"

From BuildBrighton
Jump to: navigation, search
(Status)
 
Line 7: Line 7:
  
 
=Status=
 
=Status=
 +
'''Not Working'''
 +
 +
It is suspected that the processor has been destroyed.
 +
Driver board has been dismantled.
 +
 
* Heatbed upgraded and working.
 
* Heatbed upgraded and working.
 
* All axes are working (may require further calibration in firmware).  
 
* All axes are working (may require further calibration in firmware).  
 
* All end-stops are working.  
 
* All end-stops are working.  
 
* Hot-end & thermistor are working.
 
* Hot-end & thermistor are working.
* Extruder working corectly.
+
* Extruder no longer working.
  
 
=Specs=
 
=Specs=

Latest revision as of 13:47, 18 March 2014

Introduction

From the RepRap family of open-source 3D printers.

eMaker says:

The eMAKER Huxley is one of the smallest 3D printers available at the moment in terms of footprint but not in terms of build volume. Its primary design goals were to offer a printer which was small enough to be portable, fast to replicate, and fast to assemble and commission. Since its inception at the end of 2010, the eMAKER Huxley has undergone brisk development and heavy testing. Two prototype machines have been built, although neither now looks the way it started life. The great thing about these machines being self replicating is that they can print upgrades and replacement parts for themselves.

Status

Not Working

It is suspected that the processor has been destroyed. Driver board has been dismantled.

  • Heatbed upgraded and working.
  • All axes are working (may require further calibration in firmware).
  • All end-stops are working.
  • Hot-end & thermistor are working.
  • Extruder no longer working.

Specs

  • Build volume: 140x140x90mm
  • Overall size: 260x280x280mm
  • Printing materials: ABS, PLA, 1.75mm diameter thermoplastic.
  • Build surface: Heated to ensure parts do not warp.
  • Resolution: 0.0125mm
  • Speed: 12000mm/min
  • Deposition rate: 33cm3 / hr
  • Motion: Linear bearings on X and Y axes, Igus low friction bushings on Z axis.

Source

Bought from Emaker: http://www.emakershop.com/wiki/emaker-huxley-wiki

Modifications

Firmware

Currently running the ReprapPro branch of the Marlin firmware with a few modifications to the pins.h to match our Sanguinololu 1.3a controller board.

Heatbed

Original nichrome heatbed has now been replaced with a, hopefully more reliable, reprappro PCB heatbed.

Extruder

A new extruder has been printed to replace the old unit that was causing print quality issues.

Ideas for Future Upgrades

Cooling Fan

A lot of the prints that have been attempted on this printer so far have been very small, and the plastic has not always had enough time to cool before the next layer is laid down. One of htese might help... https://github.com/reprappro/Huxley/blob/master/Print-Huxley/Individual-STLs/optional-fan-mount-1off.stl With the upgrade to the pcb heatbed we have freed up a mosfet on the controler board that could be used to turn this fan on and off in software.

Z Probe

The biggest hastle when getting the printer ready to print is setting the z height on the printer. Something like this: http://reprap.org/wiki/CrashProbe

  • note: I have all the parts for this ready to go, but it currently depends on a different firmware to the one we are using.

Spool Holder

Needed to prevent to filament getting all tangled up while printing.

Filament Storage

Need to kep the moisture content of the filament as low as possible to ensure the best quality prints. Combine this with the spool holder so that you can print without having to take the reel out of the storage box for bonus points.